|
4th March 2017, 03:17 PM | #1 |
Member
Expert member
Join Date: Feb 2012
Posts: 58
|
extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
I just upgraded from 6.8.14 to 8.0.80 and while the extrude polygon works one way in 6.8.14 (the way I want,) I can't get the 8.0.80 to work the same way. The issue is the endcap, I can't the endcap on both sides of the extruded shape in 8.0.80. I've tried extruding the surface as well as the object, I've tried pulling and pushing, but no matter what I don't get the second endcap. Here are snapshots 6.8.14 vs 8.0.80:
What gives? |
5th March 2017, 11:28 AM | #2 |
Administrator
Professional user
Join Date: Jun 2003
Posts: 4,565
|
Re: extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
Pull the divider down (underneath the Mode panel) and you'll probably find that 'Remove orig' is ticked.
|
5th March 2017, 12:44 PM | #3 |
Member
Expert member
Join Date: Feb 2012
Posts: 58
|
Re: extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
Hey!!!! look at that!!! its a drag partition and there are other options that were hidden!!! Thank you!!!!
FWIW, attention AC3D developers: there is supposed to be a drag bar indicator to the right of a boxed section if you can't see the entire box to tell the users there is more below. If you notice in the screen shot, the "Utils" boxed section is properly formed and has a drag bar to the right to tell users there is more that is not visible, When the Extrude box is too short and hides the last two checkboxes (as in my screencap shown in the original post,) you'll notice the Extrude option box does not have a drag bar on the right and I had no idea there were more options than cap end. Last edited by jleslie; 5th March 2017 at 12:49 PM. |
27th November 2018, 08:01 AM | #4 |
Junior Member
Junior member
Join Date: Mar 2011
Posts: 1
|
Re: extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
Is that missing from 8.3.11 beta? It shows just gridsnap and select through for me.
Update: I used create convex surface under the vertex menu, but I don't think that's doing exactly the same operation - I end up with a seperate surface shape with duplicate vertices I think. This seems to be a backward step - I'm going back to a previous version which is a pity since the new import formats are a big benefit. Last edited by jasonic; 27th November 2018 at 08:22 AM. |
27th November 2018, 12:10 PM | #5 |
Member
Advanced member
Join Date: May 2015
Location: CYHM
Posts: 33
|
Re: extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
As far as I recall from reading the manual, this is how it's supposed to work...
|
27th November 2018, 06:55 PM | #6 |
Administrator
Professional user
Join Date: Jun 2003
Posts: 4,565
|
Re: extruding a polygon 8.0.80 can't get endcap, what am I doing wrong?
In 8.3, the additional (and sometimes confusing options) have been removed. Extrude now works in a similar way to other software, by simply adding extra polygons at edges of a selection.
This change is primarily due to the introduction of the Object->Thicken function. With Thicken, it's easy to create shapes and then extrude them, without worrying about normals and open/closed ends (some of the options that were previously in the older versions) You might also want to use Vertex->Extrude-edges. Using this on a polygon and then dragging upwards will do the same as the previous extrude, where "cap-end" was de-selected - essentially creating a 'wall'of new polygons around the edges. Of course, you could also use Thicken and then delete some surfaces, to end up with the same shape. As Sean mentioned, the manual (available from the Help menu in 8.3) has been updated to cover the new extrude and Thicken. |
|
|