|
1st May 2014, 09:17 AM | #1 |
Member
Advanced member
Join Date: Mar 2010
Location: Norway
Posts: 45
|
Texture mapping of slanting surfaces
I've created an element that's basically a cage that encloses another structure on a roof top. I've used transparency for the grid of beams and crossbars.
The structure has rounded end sections and the top surface is smaller than the bottom surfaces--this means slanting surfaces and trapezoid / trapezium surfaces at the corners. How would you go about texture mapping this? As the attached image shows the rounded corner sections don't match up with the rest. |
2nd May 2014, 04:39 AM | #2 |
Administrator
Professional user
Join Date: Jun 2003
Posts: 4,565
|
Re: Texture mapping of slanting surfaces
The same structure in real life would need to have different sized windows/panels at the edges so you'll need to select the surfaces that need adjusting and adjust only those in the TCE. You should be able to simulate non-rectangular panels by moving the texture coordinates for those surfaces.
In the main AC3D windows, I would select the vertical strip of surfaces on the straight edge, along with the surfaces at the edge of the slanted front. Then in the TCE, line up the texture coordinates (by vertex) so they matched. |
2nd May 2014, 06:12 AM | #3 |
Member
Advanced member
Join Date: Mar 2010
Location: Norway
Posts: 45
|
Re: Texture mapping of slanting surfaces
In the meantime I've made the challenge a bit easier by adding / adjusting surfaces at the "rounded corners". A higher surface resolution helps but I will still have to do some scrunching and rotating in the end. I can also make a dedicated texture area for the corners where the vertical bars and the horizontal ones do not cross at a straight angle. That is, the vertical bars should fit a trapezoid / trapezium in the troublesome areas and be fan shaped rather than parallel.
So, there are three ways to go about a thing like this, 1) Modify / add surfaces to the model 2) Skew / rotate the texture mapping of single surfaces 3) Make a dedicated texture area to be drawn by the challenging surfaces I'm likely to end up with a combination of these approaches. |
11th May 2014, 12:50 PM | #4 |
Senior Member
Professional user
Join Date: Nov 2007
Posts: 139
|
Re: Texture mapping of slanting surfaces
Hans,
I've been meaning to ask if you would attach the original mesh and texture if you still have them? Thanks, Ron |
11th May 2014, 02:19 PM | #5 |
Member
Advanced member
Join Date: Mar 2010
Location: Norway
Posts: 45
|
Re: Texture mapping of slanting surfaces
My texture exceeds the forum upload limit. It's part of a factory plant and the texture weighs in at 581 kb. I may create a model that doesn't involve anything else, cut out the relevant part of the texture and re-texture it.
Anyway, when 581 kb is too large to upload it's pretty hard to include textures. |
12th May 2014, 11:51 AM | #6 | |
Senior Member
Professional user
Join Date: Feb 2004
Location: Portland, OR
Posts: 604
|
Re: Texture mapping of slanting surfaces
Quote:
Where there are now troublesome corners, I suggest putting some time into cutting and recombining new surface edges to fix the "overlap issues." Use the knife tool to create the new structure you need.
__________________
Flight Sim Project Contributor My Gaming Rig: i5 2500K Quad-Core CPU at 3.3GHz MSI P67A-C43 mobo 4GB of PC12800 DDR3 memory Windows 7 1GB Galaxy GeForce GTX550 Ti video card GeForce 270.61 drivers (4/2011) Cougar joystick/throttle combo CH Pedals |
|
12th May 2014, 03:44 PM | #7 |
Member
Advanced member
Join Date: Mar 2010
Location: Norway
Posts: 45
|
Re: Texture mapping of slanting surfaces
Here's a screenshot of my revised version. There's an extra surface at each corner and each of these take a skewed version of the main texture.
|
Thread Tools | |
Display Modes | |
|
|